Siemens SIMATIC NET страница 28 Скачать руководство пользователя

Страница: 28 / 464

Description

2.6 General CLI commands

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

2.6

General CLI commands

This section describes commands that you can call up in any mode.

2.6.1

clear screen

Description

With this command, you clear the screen.
The command prompt is displayed.

Syntax

Call the command without parameters:

clear screen

Result

The screen is cleared.
The command prompt is displayed.

2.6.2

Description

With this command, you can execute the commands from the Privileged EXEC mode in any

configuration mode.

Syntax

Call up the command with the following parameters:

do [command ]

To do this, you replace

[command ]

with the command from the Privileged EXEC mode that

you want to execute.
Example

do show cli-console-timeout

Result

The command from the Privileged EXEC mode will be executed.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды