Siemens SIMATIC NET страница 433 Скачать руководство пользователя

Страница: 433 / 464

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

433

Diagnostics

The monitoring of the system and error diagnostics are handled in different ways:

●

Events and faults handling:

Predefined events generate a message. These messages can be distributed in different

ways:
–

Entry in the local log

–

Transfer to the Syslog server

–

Sending as e-mail

–

Sending as SNMP trap

●

Syslog:

Configures the transfer to the Syslog server

●

Port mirroring:

Mirroring of ports to analyze the data stream without disturbing operation

11.1

Diagnostics

In events and faults handling, you set the events whose messages will be distributed in one

of the available ways.
You configure the monitoring of certain system events and power supply and physical

interfaces in the Events configuration mode.

11.1.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды