Siemens SIMATIC NET страница 343 Скачать руководство пользователя

Страница: 343 / 464

Network protocols

7.4 SNMP

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

343

Requirement

You are in the Global configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

no snmp notify <NotifyName>

The parameter has the following meaning:

Parameter

Description

Range of values / note

NotifyName

Name of the notification

max. 32 characters

Result

The details of the SNMP notifications are deleted.

Further notes

You change the details of an SNMP group with the

snmp notify

command.

You display the configured SNMP notifications with the

show snmp notif

command.

You display the configured SNMP target addresses with the

show snmp targetaddr

command.

7.4.2.14

snmp targetaddr

Description

With this command, you configure the SNMP target address.

Requirement

●

The SNMP target parameters are configured.

You are in the Global configuration mode.

The command prompt is:

cli(config)#

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды