Siemens SIMATIC NET страница 356 Скачать руководство пользователя

Страница: 356 / 464

Network protocols

7.5 SMTP client

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

356

Configuration Manual, 10/2015, C79000-G8976-C351-05

7.5.2.2

no smtp-server

Description

With this command, you delete an SMTP server entry.

Requirement

You are in the EVENTS configuration mode.
The command prompt is as follows:

cli(config-events)#

Syntax

Call up the command with the following parameters:

no smtp-server { ipv4 <ucast_addr> | fqdn-name <FQDN)>}

The parameters have the following meaning:

Parameter

Description

Range of values / note

ipv4

Keyword for an IPv4 address

ucast_addr

IPv4 address of the SMTP server

Enter a valid IPv4 unicast ad-

dress.

fqdn-name

Keyword for a domain name

FQDN

Domain name (Fully Qualified Domain

Name)

Maximum of 100 characters

For information on addresses and interfaces, refer to the section "Addresses and interface

names (Page 25)".

Result

The SMTP server entry is deleted.

Further notes

You configure an SMTP server entry with the

smtp-server

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды