Siemens SIMATIC NET страница 97 Скачать руководство пользователя

Страница: 97 / 464

Functions specific to SCALANCE

4.2 Signal recorder

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

●

The WLAN interface is enabled.

Call up the command with the following parameters:

wlan signal-recorder <wlan 0/X> stop

The parameter has the following meaning:

Parameter

Description

Range of values / note

wlan 0/X

WLAN interface

Enter a valid interface.

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The recording was stopped.

Further notes

You start the recording with the

wlan signal-recorder start

command.

4.2.4

wlan signal-recorder display (client)

Description

With this command, you configure and start recording with the signal recorder without

specifying a total for the measured values. The measured values are output in the CLI and

logged in files. The files can be downloaded as a zip file using http or tftp. The values are

stored every 10 minutes and overwrite the existing values. The file therefore contains the

values the last time they were stored.

Note
This command is only available in the client mode.

Requirement

●

The WLAN interface is enabled.

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды