Siemens SIMATIC NET Скачать руководство пользователя

Страница: 227 / 464

Network structures

6.2 VLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

227

6.2.2.5

base bridge-mode

Description

With this command, you configure whether or not the device is configured as a bridge

according to IEEE 802.1D for the Spanning Tree protocol or according to IEEE 802.1Q for a

virtual bridged LAN.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

base bridge-mode {dot1d-bridge|dot1q-vlan}

The parameters have the following meaning:

Parameter

Description

Range of values / note

dot1d-bridge

Sets the mode of the device to "transparent"

for the Spanning Tree protocol.

Default setting

dot1q-vlan

sets the mode of the device to "VLAN-aware"

for a virtual bridged LAN.

Result

The device mode is configured.

Further notes

You display the status of this function and other information with the

show vlan device info

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды