Siemens SIMATIC NET Скачать руководство пользователя

Страница: 119 / 464

System time

5.2 NTP client

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

119

5.2

NTP client

This section describes commands relevant for configuration of the NTP client.

5.2.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

5.2.1.1

show ntp info

Description

This command shows the current settings for the Network Time Protocol (NTP).

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show ntp info

Result

The current NTP settings are displayed.

5.2.2

Commands in the global configuration mode

This section describes commands that you can call up in the Global configuration mode.
In Privileged EXEC mode, enter the

configure terminal

command to change to this mode.

Commands relating to other topics that can be called in the Global configuration mode can

be found in the relevant sections.
You exit the Global configuration mode with the

end

exit

command and are then in the

Privileged EXEC mode again.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды