Siemens SIMATIC NET страница 130 Скачать руководство пользователя

Страница: 130 / 464

System time

5.3 SNTP client

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

130

Configuration Manual, 10/2015, C79000-G8976-C351-05

Requirement

●

The SNTP client is activated.

●

You are in the SNTP Configuration mode.

The command prompt is:

cli(config-sntp)#

Syntax

Call up the command with the following parameters:

sntp client addressing-mode{unicast|broadcast}

The parameters have the following meaning:

Parameter

Description

Range of values / note

unicast

configures the SNTP client in unicast

mode

Default: unicast enabled

broadcast

configures the SNTP client in broad-

cast mode

Result

The addressing mode of the SNTP client is configured.

Further notes

You display this setting and other information with the

show sntp status

command.

You display the settings for the unicast mode with the

show sntp unicast-mode status

command.
You display the settings for the broadcast mode with the

show sntp broadcast-mode status

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды