manualshive.com logo in svg

Siemens SIMATIC NET, Руководство по настройке, Страница: 190 / 464

Поделиться
Скачать
Siemens SIMATIC NET Скачать руководство пользователя страница 190

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

190

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

6.1.5.38

 

no wlan dfs multi-radar-detection 

Description  

With this command you disable access points exchanging information about radar signals 

among themselves and verifying them. 

Requirement 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call the command without parameter assignment: 

no wlan dfs multi-radar-detection

 

Result  

The function is disabled. 

Further notes 

You display the setting with the 

show wlan advanced <wlan 0/X>

 command.  

You enable the function with the 

wlan dfs multi-radar-detection

 command. 

6.1.5.39

 

wlan dtim (access point) 

Description  

With this command, you configure the DTIM interval. The DTIM interval (1-15) specifies the 

number of beacons to be sent before the access point sends the packets 

(broadcast/unicast/multicast) to the client.  
If, for example, you enter "5", this would mean that the access point collects the packets and 

sends them after every fifth beacon. 

 

 

Note 
This command is available only in access point mode. 

 

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Отзывы:

Нет отзывов