Siemens SIMATIC NET страница 40 Скачать руководство пользователя

Страница: 40 / 464

Configuration

3.1 System

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".
If you do not select any parameter from the parameter list, the entries are displayed for all

available counters.

Result

The counters of the selected interfaces are displayed.

3.1.1.8

show interface mtu

Description

With this command, you show the setting for the Maximum Transmission Unit (MTU) of the

interfaces on the device.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show interface mtu [{Vlan<vlan-id(1-4094)>|

<interface-type><interface-id>}]

The parameters have the following meaning:

Parameter

Description

Range of values / note

Vlan

Keyword for a VLAN connection

vlan-id

Number of the addressed VLAN

1 ... 4094

interface-type

Type or speed of the interface

Enter a valid interface.

interface-id

Module no. and port no. of the interface

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".
If no parameters are specified, the settings for all interfaces are displayed.

Result

The settings are displayed.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды