Siemens SIMATIC NET страница 402 Скачать руководство пользователя

Страница: 402 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

402

Configuration Manual, 10/2015, C79000-G8976-C351-05

10.2.2.12

no wlan security context (Client)

Description

With this command, you delete a security context.

Note
This command is only available in the client mode.

Note
The security context 1 cannot be deleted.

Requirement

You are in the WLAN configuration mode.
The command prompt is as follows:

cli (config-wlan)#

Syntax

Call up the command with the following parameters:

no wlan security context <ID (1-8)>

The parameter has the following meaning:

Parameters

Description

Range of values / note

ID of the security context

1...8

Result

The security context is deleted,

Further notes

You exit with the

end

exit

command.

You create a security context and change to the security context configuration mode with the

command

wlan security context

You display the setting with the

show wlan security

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды