Siemens SIMATIC NET страница 394 Скачать руководство пользователя

Страница: 394 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

394

Configuration Manual, 10/2015, C79000-G8976-C351-05

10.2.2.4

wlan security ap-radius-authenticator max-retransmit

Description

With this command, you configure maximum number of attempts to establish a connection.

Note
This command is available only in access point mode.

Requirement

You are in the WLAN Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-wlan)#

Syntax

Call up the command with the following parameters:

wlan security ap-radius-authenticator max-retransmit <index (1-2)> <1-254>

The parameters have the following meaning:

Parameter

Description

Range of values / note

index

Index of the RADIUS server

1...2

1-254

Number of connection attempts

1...5

Result

The maximum number of attempts to establish a connection is configured.

Further notes

You display the setting with the

show wlan security ap-radius-authenticator

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды