Siemens SIMATIC NET Скачать руководство пользователя страница 68

Страница: 68 / 464

Configuration

3.2 Load and Save

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

Configuration Manual, 10/2015, C79000-G8976-C351-05

File type

Description

Down-

load

Save

Delete

WLANServC

ert

(in client

mode only)

Server certificate.

WLANSigRe

(in client

mode only)

The zip file contains the following:

•

csv file with the measured values of the signal

recorder

•

pdf file with the measured values and an addi-

tional graphic representation of the measured

values.

You will find information about the measured val-

ues and their graphic representation in the section

"Signal recorder (Page 94)".

WLANSpec-

trumAnalyz-

(Only in

access point

mode)

The Zip file contains a csv file with the measured

values of the spectrum analyzer.
You will find information about the measured val-

ues and their graphic representation in the section

"Auto-Hotspot".

Table 3- 2

TFTP

File type

Description

Save

Down-

load

Config

Start configuration

ConfigPack

Detailed configuration information. for example, start

configuration, users, certificates

CountryList

The zip file contains the country list as a csv and as a

pdf file.

Debug

This file contains information for Siemens Support.

EDS

Electronic Data Sheet (EDS)
Electronic data sheets for describing devices in the

EtherNet/IP mode

Firmware

Loading firmware updates

GSDML

Information on the device properties (PNIO)

HTTPS Cert

HTTPS certificate

LogFile

File with entries from the event log table

MIB

Private MSPS MIB file "Scalance_w_msps.mib"

RunningCLI

This file contains an overview of the current configura-

tion in the form of CLI commands. You can download

the text file. The file is not intended to be uploaded

again unchanged.

Script

CLI script file

StartupInfo

Startup log file

Users

File with user names and passwords

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Siemens SIMATIC NET, Руководство по настройке, Страница: 68 / 464

Результаты поиска

Содержание SIMATIC NET

Отзывы: