Siemens SIMATIC NET Скачать руководство пользователя

Страница: 299 / 464

Network protocols

7.2 DHCP client

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

299

7.2

DHCP client

This section describes commands of the Dynamic Host Configuration Protocol (DHCP).

7.2.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

7.2.1.1

show ip dhcp client stats

Description

With this command, you display the statistical counters of the DHCP client.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameters:

show ip dhcp client stats

Result

The counters are displayed.

7.2.1.2

show ip dhcp client

Description

With this command, you display the configuration settings of the DHCP client.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды