Siemens SIMATIC NET Скачать руководство пользователя страница 264

Страница: 264 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

264

Configuration Manual, 10/2015, C79000-G8976-C351-05

Syntax

Call up the command with the following parameters:

no spanning-tree{forward-time|hello-time|max-age}

The parameters have the following meaning:

Parameter

Description

forward-time

Time after which a port changes its spanning tree status from "Blocking" to

"Forwarding"

hello-time

Time after which the bridge sends its configuration frames (BPDUs)

max-age

Time after which the information of the BPDUs becomes invalid

Result

The selected setting for the time is reset to the default value.

Further notes

You configure the time with the

spanning-tree

command (time settings).

You display these settings and other information with the commands that start with

show

spanning tree ...

6.3.4

Commands in the interface configuration mode

This section describes commands that you can call up in the Interface configuration mode.

Note
The commands are only available with layer 3 and when the interface is a VLAN interface.

In the VRRP Router configuration mode, enter the

interface

command to change to this

mode.
Commands relating to other topics that can be called in the Interface configuration mode can

be found in the relevant sections.

●

If you exit the Interface configuration mode with the

exit

command, you return to the

VRRP Router configuration mode.

●

If you exit the Interface configuration mode with the

end

command, you return to the

Privileged EXEC mode.

Requirements for changing to this mode:

●

MSTP is enabled

●

Base bridge mode: 802.1Q VLAN Bridge

●

Compatibility mode: MSTP

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Siemens SIMATIC NET, Руководство по настройке, Страница: 264 / 464

Результаты поиска

Содержание SIMATIC NET

Отзывы: