Siemens SIMATIC NET Скачать руководство пользователя

Страница: 260 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

260

Configuration Manual, 10/2015, C79000-G8976-C351-05

6.3.3.14

spanning-tree priority

Description

With this command, you configure the priority of the device. Which device becomes the root

bridge is decided based on the priority. The bridge with the highest priority becomes the root

bridge. The lower the value, the higher the priority.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

spanning-tree[mst <instance-id(1-64)>] priority <value(0-61440)>

The parameters have the following meaning:

Parameter

Description

Range of values / note

mst

Keyword for a Multiple Spanning Tree

instance

instance-id

Number of the instance

1 ... 64

priority

Keyword for the priority

value

Value for the priority

0 ... 61440
Default: 32768

You can only change the value for the priority in the steps of 4096.

Result

The priority of the device is configured.

Further notes

You can reset the setting to the default with the

no spanning-tree priority

command.

You display this setting and other information with the commands that start with

show

spanning-tree ...

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды