Siemens SIMATIC NET страница 174 Скачать руководство пользователя

Страница: 174 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface

174

Configuration Manual, 10/2015, C79000-G8976-C351-05

6.1.5.21

wlan beacon interval (access point)

Description

With this command, you specify the interval at which the SCALANCE W700 device sends

beacons. Beacons are packets that are sent cyclically by an access point to inform clients of

its existence.

Note
This command is available only in access point mode.

Requirement

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-if-wlan-0-X)#

Syntax

Call up the command with the following parameters:

wlan beacon interval <ms(40-1000)>

The parameter has the following meaning:

Parameters

Description

Range of values / note

Length of the interval in milliseconds

(ms).

40 ... 1000

Default: 100

Result

The interval is specified.

Further notes

You show the set interval with the

show wlan advanced <wlan 0/X>

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды