Siemens SIMATIC NET страница 429 Скачать руководство пользователя

Страница: 429 / 464

Security and authentication

10.3 Management Access Control List

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

429

10.3.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

10.3.1.1

show authorized-managers

Description

This command shows the information about the configuration of the authorized managers.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call up the command with the following parameters:

show authorized-managers[ip-source<ip-address>]

The parameters have the following meaning:

Parameter

Description

Range of values / note

ip-source

Keyword for the network or host ad-

dress

ip-address

Value for an IP address

specify a valid IP address

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The information about the configuration of the authorized managers is displayed.

10.3.2

Commands in the global configuration mode

This section describes commands that you can call up in the Global configuration mode.
In Privileged EXEC mode, enter the

configure terminal

command to change to this mode.

Commands relating to other topics that can be called in the Global configuration mode can

be found in the relevant sections.
You exit the Global configuration mode with the

end

exit

command and are then in the

Privileged EXEC mode again.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды