Siemens SIMATIC NET страница 389 Скачать руководство пользователя

Страница: 389 / 464

Security and authentication

10.2 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

389

Syntax

Call up the command with the following parameters:

show wlan security <wlan 0/X | vapX 0/Y> [context <Id (1-8)>]

The parameters have the following meaning:

Parameter

Description

Range of values / note

wlan 0/X

WLAN interface

Only available in client mode

Enter a valid interface.

vapX 0/Y

VAP interface

Only available in Access Point mode

Enter a valid interface.

context

Keyword for a security context

Enter a valid security context ID.

Available only in client mode
1...8

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The settings are displayed.

10.2.1.2

show wlan security ap-radius-authenticator (Access Point)

Description

This command shows the settings of the RADIUS server.

Note
This command is available only in access point mode.

Requirement

You are in the User EXEC mode or in the Privileged EXEC mode.
The command prompt is as follows:

cli>

cli#

Syntax

Call the command without parameter assignment:

show wlan security ap-radius-authenticator

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды