Siemens SIMATIC NET страница 31 Скачать руководство пользователя

Страница: 31 / 464

Description

2.6 General CLI commands

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

2.6.5.2

The command "?"

Description

With this command, you call up the command list.

Syntax

Enter a question mark to obtain a list of all permitted commands in the current mode:

For this command, you do not need to press the enter key. The command executes

immediately after you type the character.

Result

The mode-specific as well as the global commands are displayed.

Note
Incomplete command names
If you have specified an incomplete command when calling the help function, a list of all

commands that start with the term you have entered is created.

Note
Output in pages
With long lists, the results are displayed as pages. If

-- more --

appears at the lower edge of

the display, you can move to the next page with the spacebar. If the display is in pages, you

cannot page back. You exit the page display with the

key.

2.6.5.3

Completion of command entries

Description

The command interpreter of the Command Line Interface supports you when you enter

commands.
As soon as the first characters of the command have been entered in the input line, the

system can complete the entry as long as the character string is unambiguous.
This can be repeated after entering further characters.

Procedure

Enter the first characters of the command.
Press the tab key.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды