Siemens SIMATIC NET страница 121 Скачать руководство пользователя

Страница: 121 / 464

System time

5.2 NTP client

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

121

5.2.3.1

ntp server

Description

With this command, you configure the connection to a server on the NTP client.

Requirement

You are in the NTP configuration mode.
The command prompt is as follows:

cli(config-ntp)#

Syntax

Call up the command with the following parameters:

ntp server{ipv4 <ip_addr> | fqdn-name <FQDN>}[port<123,1025-36564>][poll<seconds(64-

1024)>]

The parameters have the following meaning:

Parameter

Description

Range of values / note

ipv4

Keyword for an IPv4 address

ip_addr

Value for the IPv4 address of the time

server

Enter a valid IPv4 address.

fqdn-name

Keyword for a domain name

FQDN

Domain name (Fully Qualified Domain

Name)

Maximum of 100 characters

port

UDP port of the time server

•

123

•

1025 … 36564

Default: 123

poll

Keyword for the time after which the

time of day is requested again

seconds

Value for the time in seconds

64 … 1024

For information on identifiers of addresses and interfaces, refer to the section "Addresses

and interface identifiers (Page 25)".

Result

The connection to a server is configured on the NTP client.

Further notes

You delete the connection to a server with the

no ntp server

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды