Siemens SIMATIC NET страница 177 Скачать руководство пользователя

Страница: 177 / 464

Network structures

6.1 WLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

177

6.1.5.24

wlan client mac address (client)

Description

With this command, you specify the MAC address of the client.

Note
This command is only available in the client mode.

Requirement

●

The MAC address is assigned to the client manually.

You are in the Interface Configuration mode of the WLAN interface.
The command prompt is as follows:

cli (config-if-wlan-0-X)#

Syntax

Call up the command with the following parameters:

wlan client mac address <mac address>

The parameter has the following meaning:

Parameters

Description

Range of values / note

mac address

MAC address of the client

aa:aa:aa:aa:aa:aa

Result

The MAC address was assigned to the client.

Further notes

You display the setting with the

show wlan client <wlan 0/X>

command.

Содержание SIMATIC NET

















































































































































































































































































































































































































































































Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды

Siemens SIMATIC NET, Руководство по настройке

Результаты поиска

Содержание SIMATIC NET

Отзывы:

Похожие инструкции для SIMATIC NET

Бренды по названию

Популярные бренды