Siemens IM 153-4 PN Скачать руководство пользователя страница 92

Страница: 92 / 274

Commissioning

6.1 PROFIBUS DP

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Requirements for commissioning

The following conditions must be fulfilled in order to commission the ET 200M:
●

DP slave installed

●

PROFIBUS address set on the DP slave

●

Bus connector or FOC is connected

●

Only for DP interface RS 485:
If the DP slave is located on the end of the segment, then the terminating resistor is

switched on the DP slave.

●

Only for DP interface FOC:
If the DP slave is located at the end of an FOC line, then the unused FOC interface must

be closed with a dummy plug.

●

DP slave configured (refer to the online help / manual on configuration software)

NOTICE

when configuring with GSD file
When using an IM 153-2BA81 (outdoor) you must convert the user parameter "MLFB" to

6ES7153-2BA81-0XB0.
If you configure the ET 200M (IM 153-2BAx2) with a GSD file, the length of the

parameter assignment message frame (maximum 244 bytes) can lead to limitations in

the number of assignable modules.

●

Supply voltage for DP master switched on (refer to the DP master manual)

●

Configuration loaded into the DP master (refer to the online help / manual on

configuration software)

●

DP master switched to RUN (refer to the DP master manual)

Commissioning the DP slave

Commission the DP slave as follows:
1.

Switch on the supply voltage for the DP slave.

If necessary, switch on the supply voltage for the load.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды