Siemens IM 153-4 PN Скачать руководство пользователя страница 187

Страница: 187 / 274

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

185

Interrupt, error and system messages

9.1

PROFIBUS DP

9.1.1

Diagnostics with LED display

Status and error displays of the IM 153-1

21 6XSSO\ YROWDJH DY

DLODEOH

*UHHQ

%) (UURU RQ WKH 352)

,%86'3

5HG

6) *URXS HUURU

5HG

6)
%)

Table 9- 1

LEDs

Meaning

Remedy

off

No voltage on the IM 153-1 or there is a

hardware fault with the IM 153-1.

Switch on the power supply module or replace the

IM 153-1.

There is voltage on the IM 153-1.

—

flashes on

IM 153-1 is incorrectly configured - no data

exchange is taking place between the DP

master and the IM 153-1.
Causes:

•

Configured and set PROFIBUS address is

incorrect

•

Faults on the bus

•

Check the IM 153-1.

•

Check the configuration and parameter

settings.

•

Check the PROFIBUS address on the IM 153-

1 and in the STEP 7 project.

•

Check the cable length with reference to the

baud rate.

•

Check the settings for the terminating

resistors.

no connection to the DP master (search baud

rate)
Causes:

•

the bus communication via PROFIBUS DP

to the IM 153-1 has been interrupted

Check the bus configuration.

•

Check to see if the bus connector is inserted

properly.

•

Check whether the bus cable to the DP master

is defective.

•

Switch off and on the on / off power switch for

the 24 V DC on the power supply module.

flashes on

The configured structure of the ET 200M

doesn´t tally with the actual structure of the ET

200M

Check the PROFIBUS address and the

configuration of the ET 200M to see if a module is

missing, faulty or if there is a non-configured

module.
Check the configuration (e.g. with

COM PROFIBUS

STEP 7

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды