Siemens IM 153-4 PN Скачать руководство пользователя страница 82

Страница: 82 / 274

Connecting

5.4 Wiring the power supply and modules

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Wiring a power supply and IM 153-x with jumper

In order to wire power supply modules and IM 153-x, proceed as follows (refer to the

following figure):

WARNING

Ensure the ET 200M is de-energized before doing any wiring!

Open the front panels of the PS 307 and the IM 153-x.

Undo the strain relief assembly on the PS 307.

Insulate the power cable (230 V / 120 V) and connect this to the PS 307.

Screw the strain relief assembly tight again.

Insert the jumper and screw it tight.

Close the front doors.

[

Figure 5-2

Wiring a power supply module PS 307 and IM 153-x with jumper

①

Strain relief

②

Jumper

Setting the Switch for the Mains Voltage

Check that the switch for selecting the mains voltage is set correctly to your mains voltage.

This switch is always factory-set to 230 V on the PS 307. To select another mains voltage,

do the following:
1.

Prize the cover off with a screwdriver.

Set the selector to your mains voltage.

Place the cover back onto the switch opening.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды