manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 231

 

Technical Specifications 

 

10.2 Parameters of the IM 153-x 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

229

 

Use in residential areas   

If you use the ET 200M in residential areas, you must ensure that the radio interference 

emissions comply with limit value class B in accordance with EN 55011. 
The following measures are recommended to ensure the interference complies with limit 

value class B: 
●

 

Install the ET 200M in grounded switching cabinets/boxes 

●

 

Use of noise filters in the supply lines 

 

WARNING 

 

 

There is a risk of injury or of damage to assets. 
In potentially explosive environments, there is a risk of injury or damage if you 

disconnect any connectors while the ET 200M is in operation. 
In explosive environments, always isolate the ET 200M before you disconnect 

connectors.  

 

Laser protection classes authorization (for the IM 153-2 FO) 

Class 1 in accordance with EN 60825-1: 1994+A11: 1996 or IEC 60825-1: 1993 including 

amendment 1:1997  
In the case of an intentional / unintentional opening of the accessible FOC radiation in 

accordance with degree of endangering 1 as per EN 60825-2: 1994 or IEC 60825-2: 1993. 

10.2

 

Parameters of the IM 153-x 

Parameter assignment 

You configure the IM 153-x or the ET 200M with 

STEP 7 or COM PROFIBUS. If you use a 

different configuration tool, you must integrate the GSD file.  

Table 10- 2  Parameters of the IM 153 x 

Parameters 

Range of values 

Default 

Scope 

DPV1 mode 

block / enable 

enable 

ET 200M 

Start up at preset ≠ actual 

configuration? 

yes/no 

No 

ET 200M 

"Module change during 

operation"? 

yes/no 

No 

ET 200M 

Diagnostic Interrupt 

block / enable 

enable 

ET 200M 

Process interrupt 

block / enable 

enable 

ET 200M 

Removing / insertion interrupt 

block / enable 

enable 

ET 200M 

Analog-value format 

SIMATIC S7 / SIMATIC S5 

SIMATIC S7 

ET 200M 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды