manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 152

Functions 

 

8.2 Time stamping the input signals with IM 153-2 

 

ET 200M 

150

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Step 

Activity 

Description 

6. 

Diagnose imminent signal 

messages and save the 

information. 
Ensure that when a process 

interrupt is received the block 

"RALRM" is active. You must wire 

this block. 

When signal messages arrive the slave sends a 

process interrupt to the master. The master then 

asks for a diagnosis from the slave. 
The slave responds with the diagnostic frame. 
Based on this diagnostic frame, the block "RALRM" 

must be started via the user program. This block 

reads TINFO and AINFO in the memory. The 

relevant information for this is: 

•

 

diagnostic address of the slave 

•

 

number of the data record 

•

 

number of messages in the data record 

the new bit is set from the "RALRM" block to "1" 

after the data transmission.  

7. 

With the "RDREC" block, read the 

signal messages from the reported 

data record. You must wire this 

block. 

You must ensure that the "RDREC" block is 

processed in the user program. In the case of 

imminent messages (signaled by the new bit from 

the "RALRM" block) this reads the reported data 

record (100 to 114) and saves it in the specified 

target range (e.g. DB 46). 
Before the "RDREC" block is active, the following 

values from "RALRM" must be changed: 

•

 

diagnostic address of INT → DINT 

•

 

data record number of BYTE → INT 

8. 

Reset the NEW bit on the "RALRM" 

block. 

If the values of the data record are read and are to 

be saved for further processing, the NEW bit on the 

"RALRM" block must be reset. 

 You must carry out this step. 

You can now read further data records (steps 6 to 8). 

8.2.4.4

 

Time synchronization 

For the time synchronization with time stamping outside of S7-400 the requirements 

specified in the chapter "Time synchronization for time stamping (Page 135)" apply. 
The parameters for the IM 153-2 must be set via the GSD file. 

8.2.4.5

 

Configuring the time stamping 

For configuring the time stamping of input signals the IM 153-2 makes available an interface 

in the form of the data record 240. There you can choose your requirements accordingly, 
●

 

whether the time stamping should be generally activated / deactivated 

●

 

on which slot a module is inserted, the input signals of which should be stamped 

●

 

which signals receive a time stamp (via "DI n Enable": time stamping activated / 

deactivated) 

●

 

which signal change will be stamped in which way (via "DI n Edge": "rising" edge as an 

incoming signal or "falling" edge as an incoming signal).  

The unselected edge is automatically the outgoing signal, i.e. both changes of a signal 

are given a time stamp. 

With DS_WRITE the data record 240 is transferred to the IM 153-2 for the configuration of 

the time stamp. 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды