Siemens IM 153-4 PN Скачать руководство пользователя страница 66

Страница: 66 / 274

Installation

4.2 Installation

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Sequence when hanging the modules

Hang the modules onto the rail as follows:
1.

Power supply module

IM 153-x

Signal module(s)

Note
If you are installing SM 331 analog input modules, please check before installation

whether you have to move the measuring range submodules on the side of the module.

(Refer to chapter "Analog modules" in the "S7-300 automation system, module

specifications (

http://support.automation.siemens.com/WW/view/en/8859629

)" reference

manual.)

Sequence for Installation

Proceed as follows to install the modules:

Table 4- 3

Installing modules on mounting rails

Step

Activity

Figure

Hook the power supply unit PS 307 onto the rail

and screw it tight.

Clip on the bus connector.
A bus connector is included with each signal

module, but not however with the IM 153-x. When

installing the bus connector always start with the IM

153-x:

•

Take the bus connector from the "last" module

and insert it in the IM 153-x.

•

Do not plug a bus connector into the "last"

module.

Do not insert any bus connectors between the PS

307 and IM 153-x!

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды