manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 81

 

Connecting 

 

5.4 Wiring the power supply and modules 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

79

 

5.4.2

 

Wiring the Power Supply and IM 153-x 

Power Cables 

Use flexible cables to wire the power supply.  
If you use only one cable per connection, you don't need an end ferrule. 

Jumper 

Use the jumper to wire the power supply module PS 307 with the IM 153-x. The jumper 

comes with the power supply module.  

Further 24 V connections 

On the power supply PS 307 via the jumper an additional 24 V-connections are still free for 

connecting the supply of the S7-300 modules. 

Wiring the 24 V connections with redundant configuration with 2 x IM 153-2 

 

 

Note 
If, in a configuration for redundancy, you connect the supply voltage L+ when wiring to the 

IM 153-2, this brings about a short circuit via the ground terminal.  

Reason: The two IM 153-2 have a mutual ground cable via the BM IM /IM bus module. 
with IM 153-2AA02 / -2AB01: 

We recommend, with a redundant configuration, that you protect the L+-supply from the 

IM 153-2 with 2.5 A. 
with IM 153-2Bx00 / -2Bxx1: 

•

 

In configurations with ungrounded reference potential (jumper between M and functional 

ground removed, see the figure in the "Configuration of an ET 200M with ungrounded 

reference potential (Page 54)" chapter), in the case of a polarity reversal an internal 

electronic fuse is triggered and this regenerates after approx. 30 seconds. 

•

 

With a configuration with grounded reference potential (bridge inserted between M and 

functional earth) when connection this brings about a short circuit current via this bridge 

and the functional earths. 

In doing so, the IM 153-2 is not damaged if a protection is built in before the module 

which is designed in accordance with the cross-section of the connection line. 

 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды