Siemens IM 153-4 PN Скачать руководство пользователя страница 164

Страница: 164 / 274

Functions

8.4 Redundancy with IM 153-2

ET 200M

162

Operating Instructions, 12/2008, EWA-4NEB780600602-08

8.4

Redundancy with IM 153-2

Use

You can operate the interface module IM 153-2 redundantly
●

on the SIMATIC S7-400H (e.g. CPU 417-4H)

●

with GSD file on any DP master (e.g. S5-115H)
When configuring with a GSD file, the redundant operation of the IM 153-2 interface

module can take place only in DPV0 mode. This operating mode is set differently

dependent on the configuration tool.

●

with software redundancy
For the basic package

STEP 7, the optional software SIMATIC S7 Software Redundancy

is required. The optional software includes an online help in which the use and function of

the software redundancy is described.

●

to standard
Specification slave redundancy V1.2, Nov. 2004 of the PROFIBUS user organization;

order no: 2.212
–

System Redundancy (SR)

–

Flying Redundancy (FR)

Conditions for the ET 200M

●

Configuration with active bus modules
The configuration with active bus modules 6ES7195-7HD10-0XA0 or

6ES7195-7HD80-0XA0 ensures a greater availability of the ET 200M.

●

2 x IM 153-2 on bus module BM IM/IM
The arrangement specifications named in the chapter "Installation (Page 59)" apply to the

active bus modules and interface modules used.

●

Software redundancy and system redundancy (SR) are possible with the

IM 153-2 / -2 FO as of 6ES7153-2AA02-0XB0 / -2AB01-0XB0

●

Flying redundancy (FR) is possible with IM 153-2 / -2 FO as of 6ES7153-2Bxx1-0XB0
–

The redundant master system must be configured in accordance with the demands on

H systems.

–

The GSD file of the IM 153-2 (GSD rev. 5) must be imported to the configuration tool.

Note
STEP 7 offers no support for configuring an H system with flying redundancy.

●

In redundant mode the function SYNC / FREEZE is not activated.

Note
If the function SYNC / FREEZE is nevertheless activated in a redundant system, the user

bears the responsibility for the behavior of the H system (e.g. when changing over).

●

In a redundant system, you can only use the IM 153-2 interface module on DP masters

that support the "fail safe" parameter. The IM 153-2 will not run on DP masters that do not

support this parameter, and the BF LED flashes.
Tip: You can see in the GSD-file of the DP master whether this "fail safe" is supported.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды