Siemens IM 153-4 PN Скачать руководство пользователя страница 70

Страница: 70 / 274

Installation

4.2 Installation

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

4.2.5

After installation

Assign slot numbers

After installation you can assign a slot number to each module, and this makes it easier to

assign the modules to the configuration table in

STEP 7 or in COM PROFIBUS. The

following table illustrates the assignment of the slots.

Table 4- 4

Slot numbers for S7 modules

Slot number

Module

Remark

Power supply (PS)

–

IM 153-x

–

inapplicable

1. S7-300 module

right alongside the IM 153-x

2. S7-300 module

–

…

–

8. S7-300 module

–

The use of the power supply is optional.

Unoccupied slots

If, in a configuration of an ET 200M with active bus modules, slots are unoccupied (e.g.

reserved for later use), then you must leave these slots free in the configuration in

STEP 7 or

COM PROFIBUS!

Attaching slot numbers

The following figure shows how you must attach the slot numbers. The slot number plates

are provided with the IM 153-x.

Figure 4-3

Attach the slot numbers to the modules.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды