Siemens IM 153-4 PN Скачать руководство пользователя страница 189

Страница: 189 / 274

Interrupt, error and system messages

9.1 PROFIBUS DP

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

187

LEDs

BF /

BF1

ACT

Meaning

Remedy

flashes off

IM 153-2 is incorrectly configured - no

data exchange is taking place between

the DP master and the IM 153-2.
Causes:

•

PROFIBUS address is incorrect

•

Faults on the bus.

•

Check the IM 153-2.

•

Check the configuration and

parameter settings.

•

Check the PROFIBUS address on

the IM 153-2 and in the STEP 7

project.

•

Check the cable length with

reference to the baud rate.

•

Check the settings for the

terminating resistors.

off

no connection to the DP master (search

baud rate)
Causes:

•

the bus communication via PROFIBUS

DP to the IM 153-2 has been

interrupted

Check the bus configuration.

•

Check to see if the bus connector /

FOC is inserted properly.

•

Check whether the bus cable / FOC

to the DP master is defective.

•

Switch off and on the on / off power

switch for the 24 V DC on the power

supply module.

flashes off

The configured structure of the ET 200M

doesn´t tally with the actual structure of

the ET 200M

Check the configuration of the ET 200M

to see if a module is missing, faulty or if

there is a non-configured module.
Check the configuration (e.g. with

COM PROFIBUS

STEP 7

off

inadmissible PROFIBUS address

Is the SF LED of an SM / FM also lit?

•

If so: Error or diagnosis in an S7 300

module

•

If not: IM 153-2 is faulty.

On the IM 153-2 set a valid PROFIBUS

address (1 to 125)
Check the SM / FM with the

diagnostics. Replace the S7-300

module or the IM 153-2 or contact your

Siemens representative.

off

The IM 153-2 is exchanging data with the

DP master and the I/O modules of the ET

200M.

In redundant mode this IM 153-2 is the

active one of the ET 200M.

—

off

There is voltage on the IM 153-2.

In redundant mode this IM 153-2 is the

passive one, i.e. no data exchange with

the I/O modules.

—

flashes

0.5 Hz

off

In redundant mode, this IM 153-2 is the

passive, and is not ready for a fault-free

changeover (e.g. associated CPU in

STOP mode).

Switch the H system to redundant

mode.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды