manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 198

Interrupt, error and system messages 

 

9.1 PROFIBUS DP 

 

ET 200M 

196

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

Station status 2 

Table 9- 5 

Structure of station status 2 (Byte 1) 

Bit 

Meaning 

0 

1:  The DP slave must be reconfigured. 

1 

1:  The slave is in start-up phase. 

2 

1:  The bit in the DP slave is always "1". 

3 

1:  Response monitoring has been enabled for this DP slave. 

4 

1:  The DP slave has received the "FREEZE" control command. 

5 

1:  The DP slave has received the "SYNC" control command. 

6 

0:  The bit is always at 0. 

7 

1:  The DP slave is deactivated, that is to say, it has been removed from the current 

processing. 

Station status 3 

Table 9- 6 

Structure of station status 3 (Byte 2) 

Bit 

Meaning 

0 to 6 

0:  The bits are always at "0". 

7 

1:  There are more channel-specific diagnostic messages than can be represented in the 

diagnostic frame. 

9.1.3.3

 

Master PROFIBUS address 

Definition 

The PROFIBUS address of the  

DP master is stored in the master PROFIBUS address diagnostic byte:  
●

 

which the DP slave has configured and 

●

 

has read and write access to the DP slave. 

The master PROFIBUS address is located in byte 3 of the slave diagnosis. 

FF

H

 in byte 3 

If the value FF

H

 in byte 3 is given as the master PROFIBUS address, the DP slave is not 

configured by the DP master. 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды