Siemens IM 153-4 PN Скачать руководство пользователя страница 106

Страница: 106 / 274

Maintenance and service

7.3 replacing the IM 153-1

ET 200M

104

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Response of the ET 200M After Module Replacement

If there is an error after replacing the module, with

STEP 5 or STEP 7 you can view the

cause of the error in the diagnostics buffer.

7.3

replacing the IM 153-1

Initial Situation

The IM 153-1 is installed. A new IM 153-1 of the same type should be installed.

Slot numbering

If you have provided the modules in your system with slot numbering, when replacing

modules you must remove the numbering from the old module and then reuse it in the new

module.

Pull out the bus connector

You can remove the bus connector with worn-through bus cable from the PROFIBUS DP

interface without having to interrupt the data traffic to the bus.

Note
A data communication error may occur on the network.
A bus segment must always be terminated at both ends with the terminating resistor. For

example, this is not the case when the last slave with the bus connector is deactivated. As

the terminating resistor in the bus connector obtains its voltage from the node, the function of

the terminating resistor is affected.
Ensure that the nodes to which the terminating resistor is connected are always supplied

with voltage.

Tip: Use the PROFIBUS terminator as an active bus connector.

Removing a Module

To remove the module, proceed as follows:
1.

Switch the on / off switch of the power supply module to position 0 ( : output voltages

0 V).

Tighten the bus connector.

Disconnect the wiring.

Loosen the fixing screws of the IM 153-1.

Swing out the IM 153-1.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды