manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 115

 

Maintenance and service 

 

7.7 Replace modules with the function "Change During Operation" 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

113

 

7.7

 

Replace modules with the function "Change During Operation" 

Requirements 

You can replace the modules while operating the ET 200M if the ET 200M 
●

 

on the rail with active bus modules for the function "Module Change During Operation" 

●

 

and the ET 200M is configured for "Module Change During Operation". 

 

WARNING 

 

 

Inserting output modules can lead to uncontrolled system states! 
This also applies if you insert input / output modules tilted on the bus module. 
When inserting an output module, the outputs set by the user program become active 

immediately! 
We therefore advise you to set the outputs to "0" in the user program when removing 

the output module. 
If modules are not removed and inserted properly, neighboring modules via the 

backplane bus can fail. 

 

Removing a Module 

When removing modules with "Module Change During Operation" proceed as follows: 
1.

 

Release the fixing screw(s) on the module. 

2.

 

Swing the module out. 

3.

 

Open the front door. 

4.

 

Unlock the front connector and remove it. 
–

 

With 20-pin front connector: To do this, use one hand to press the unlocking button 

down (4) and use your other hand to remove the front connector via the gripping 

surface (4a). 

–

 

With 40-pin front connector: Release the fixing screw in the centre of the front 

connector. Use the gripping surface to pull out the front connector. 

5.

 

Pull the labeling strips out of the module. 

(7

D

 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды