Siemens IM 153-4 PN Скачать руководство пользователя страница 151

Страница: 151 / 274

Functions

8.2 Time stamping the input signals with IM 153-2

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

149

8.2.4.3

Brief introduction to commissioning the time stamping

If you use the DPV1 blocks "RALMR" and "RDREC", then commission an ET 200M with time

stamping of the input signals as follows:

Step

Activity

Description

Provide the DP master with the

GSD file.

The information as to which DPV1 slave

(IM 153-2BAx1) it must expect on the

PROFIBUS DP, is obtained by your DP master from

the GSD file.

The GSD file for the IM 153-2BAx1 can be found in

the Internet

(

http://support.automation.siemens.com/WW/view/e

n/113498

Integrate the slave with the DP

master.

Add the IM 153-2 to the DP line of your master

system and enter the used modules as of slot 4 of

the ET 200M.

Set the mode of synchronization

and synchronization interval for the

master and slave.

Master:

•

Type of synchronization: Master

•

Synchronization interval: e.g. 10 s

Slave:

•

Time synchronization: active

•

Synchronization interval: e.g. 10 s

The synchronization intervals for master and slave

must be the same.

Commission the ET 200M on the

PROFIBUS DP.

•

Transfer the settings to the master.

•

Connect the master and slave.

•

Check the set slave address.

•

Switch the unit on.

After start-up the slave communicates with the

master without interruption i.e. the LED "ON" lights

up and the LED "BF1" is off.
If this is not the case, you should either read and

evaluate the diagnostics data from the slave or use

a PROFIBUS monitor to analyze the

communication.

Enable the time stamping.

The time stamping is activated by writing the data

record 240 on the IM 153-2.
The data record 240 essentially stipulates

•

at which slots which channels are supposed to

be time stamped

•

which signal change (0 → 1 or 1 → 0) leads to an

incoming or outgoing message

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды