Siemens IM 153-4 PN Скачать руководство пользователя страница 145

Страница: 145 / 274

Functions

8.2 Time stamping the input signals with IM 153-2

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

143

8.2.4

Time stamping outside of S7-400

8.2.4.1

Prerequisites

With the interface module IM 153-2Bxx1, time stamping is also possible outside of an S7-

400 automation system.
The above principles and rules apply - if complied with, precisions of up to 1 ms can be

achieved.
Synchronization interval for the time: 10 s

Demands on the ET 200M and DP master

ET 200M:
●

IM 153-2 as of order number 6ES7153-2Bxx1-0XB0

●

suitable DI modules

●

IM 153-2 must be configured via GSD rev. 5 (e.g. enabling of interrupts)

●

for IM 153-2 the DPV1 mode must be activated

●

Synchronization interval in accordance with the setting on the clock master

DP master:
●

must fulfill requirements in accordance with DPV1

●

must be able to process interrupts

●

must be able to process data records (read / write)

●

must be able to send / forward time message frames or a clock master must be available

in the same PROFIBUS DP line

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды