Siemens IM 153-4 PN Скачать руководство пользователя страница 197

Страница: 197 / 274

Interrupt, error and system messages

9.1 PROFIBUS DP

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

195

9.1.3.2

Station statuses 1 to 3

Definition

The stations status 1 to 3 provides an overview of the status of a DP slave.

Station status 1

Table 9- 4

Structure of station status 1 (Byte 0)

Bit

Meaning

Cause / remedy

0 1: The DP slave cannot be addressed by the DP

master. The bit in the DP slave is always 0.

•

Is the correct PROFIBUS address set on the DP slave?

•

Bus connector / FOC connected?

•

Voltage on DP slave?

•

RS 485 repeater set correctly?

•

Has a reset been performed on the DP slave (switch off /

switch off)?

1 1: DP slave is not ready for the data exchange.

•

Wait for the DP slave to complete start-up.

2 1: The configuration data sent to the DP slave by the

DP master does not match the actual configuration

of the DP slave.

•

Correct station type or correct configuration of the DP

slave entered in the configuration software?

3 1: External diagnostics available.

•

Evaluate the identifier-related, module status and / or

channel-related diagnosis. As soon as all errors are

remedied the bit 3 is reset. The bit is reset when there is

a new diagnostic message in the bytes of the

diagnostics indicated above.

4 1: The requested function is not supported by the DP

slave.

•

Check the configuration.

5 1: The DP master cannot interpret the response of

the DP slave.

•

Check the bus configuration.

6 1: DP slave type does not correspond to the software

configuration.

•

Was the configuration software set for the correct station

type?

7 1: DP slave was configured by a different DP master

(not by the DP master that currently has access to

the DP slave).

•

The bit is always 1, for example, if you access the DP

slave with the programming device or another DP

master.
The PROFIBUS address of the DP master that

configured the DP slave is located in the "Master

PROFIBUS address" diagnostic byte.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды