Siemens IM 153-4 PN Скачать руководство пользователя страница 46

Страница: 46 / 274

Assignment planning

3.5 Configuring the mechanical structure

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

3.5.4

Arrangement of the modules for the function "Change During Operation" and / or

"Redundancy"

Arrangement rules

The following rules apply to the location of the modules in an ET 200M:
●

An ET 200M can only be installed on one mounting rack (rail), because coupling to other

mounting racks via interface modules is not permissible.

●

A maximum of 8 signal modules, function modules or communication processors may be

inserted to the right alongside the IM 153-x.

●

The IM 153-x and all the SM / FM / CP must be connected to active bus modules.

With the respective configuration, you can compatibly operate the combinations of interface

modules IM 153-2 specified in the following table on active bus modules BM IM/IM.

Table 3- 3

Compatible versions of the IM 153-2 interface module

If the redundant IM 153-2 are

configured as ...

... and the interface modules are

connected to the active bus

module 6ES7195-…,

then the following IM 153-2 can

be operated compatibly:

7HD00-0XA0

IM 153-2AA02

IM 153-2BA00

IM 153-2BAx1

IM 153-2AA02

7HD10-0XA0

IM 153-2BA00

IM 153-2BAx1

IM 153-2BA00

7HD10-0XA0

IM 153-2BA00

IM 153-2BAx1

7HD10-0XA0

IM 153-2BAx1

IM 153-2BA01

7HD80-0XA0

IM 153-2BAx1

IM 153-2BA81

7HD80-0XA0

IM 153-2BA81

7HD00-0XA0

IM 153-2AB01

IM 153-2BB00

IM 153-2AB01

7HD10-0XA0

IM 153-2BB00

7HD10-0XA0

IM 153-2BB00

Note
The active bus modules 6ES7195-7HD10-0XA0 and 6ES7195-7HD80-0XA0 are given two

yellow markings for easier identification. These marks indicate that only IM 153-2Bx00 or

IM 153-2Bxx1 can be connected to these bus modules.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды