Siemens IM 153-4 PN Скачать руководство пользователя страница 123

Страница: 123 / 274

Maintenance and service

7.10 Updating the IM 153-x

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

121

Restart After Update

Update via PROFIBUS DP
In the

STEP 7 user interface, it is possible to set whether

●

the IM 153-2 should automatically perform a reset after a successful update, in order to

start off using the new firmware.

CAUTION

If the "activate firmware after download" field is checked there is a brief station failure of

the ET 200M. If no provisions have been made for this case, then the update causes the

CPU to STOP on account of rack failure.

●

the IM 153-2 must be reset by switching off the supply voltage. Then, when the supply

voltage is switched on again the IM 153-2 will start up using the new firmware.

Update via SIMATIC Micro Memory Card
After the update the IM 153-2 remains in a state that can only be reset by switching off the

supply voltage. After a successful update, the next time the supply voltage is switched on the

IM 153-2 starts up with the new firmware.

Update unsuccessful

If the update fails, the next time the supply voltage is switched off / on the IM 153-2 starts up

with the former (old) firmware.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды