Siemens IM 153-4 PN Скачать руководство пользователя страница 169

Страница: 169 / 274

Functions

8.5 System modification during operation

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

167

Make the appropriate modifications to the configuration offline (remove or add module).

Note
The parameters of a module can only be changed by making two configuration

modifications in RUN:
1. Remove the module.
2. Add the module with new parameters.

Switch one master of the redundant system to passive (all slaves are active at the other

master).

Load the configuration in the master on the passive line and restart the master →

The parameters and configuration data are loaded in the slave.

Switch over to the line with the new configuration →

The previously loaded configuration now becomes effective. Removed modules are taken

out of the data communication and added modules with the new parameters are included

in the data communication.

The changes are checked by the user.

If the changes are OK, the new configuration must also be loaded in the second master.

If the changes are not OK, the previous status can be restored by switching over to the

second master (with the old configuration). In this case, the old configuration must be

loaded on the first master again.

Note
A reconfigured module can be removed and inserted both before and after system

modification during operation (RUN). It is first available for the process when it is really

inserted and the IM 153-2 that contains the configuration for the module is active.

NOTICE

It is the user's responsibility to ensure that the configuration within the master system is

uniform. It is not shown when the two IM 153-2 are running with different configurations.

If the two masters in the redundant system have different configurations, a system

modification during operation is carried out whenever a switchover is performed.
Interrupts and diagnoses that are generated by the IM 153-2 for an I/O module will be

reported by the passive IM 153-2 to the master, even if this module is not available in the

configuration of the passive IM 153-2. The user himself must decide to which extent the

interrupts and diagnoses from the passive IM 153-2 should be ignored during the period of

differing configuration data.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды