Siemens IM 153-4 PN Скачать руководство пользователя страница 18

Страница: 18 / 274

Product overview

1.4 ET 200M distributed I/O device

ET 200M

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Components

Function

Diagram

IM 153-x
Accessories:

•

Slot number plate (for the assignment of slot

numbers)

... is the interface module; links the

S7-300 modules to the PROFIBUS DP /

PROFINET IO; supplies the backplane

bus with operating voltage.

PROFIBUS cable with bus connector

... combines nodes of a PROFIBUS DP

configuration with each other.

FOC duplex cable with simplex connector (in the plug

adapter for the IM 153-2 FO)

... combines nodes of a PROFIBUS DP

configuration with each other.

PROFINET connector as per the specifications in the

PROFINET Installation Guide and Industrial Ethernet

FC installation lines

... connects nodes of a PROFINET IO

configuration with one another.

Signal modules (SM)
Accessories:

•

Front connectors

•

Bus connectors

... adapt differing process signal levels.

Function modules (FM)
Accessories:

•

Front connectors

•

Bus connectors

... for time-sensitive and memory-

intensive process signal processing

tasks, e.g. positioning or controlling.

Communication processor (CP)
Accessories:

•

Connecting cable

... relieves the CPU from communication

tasks.

SIMATIC TOP connect
Accessories:

•

Front connector with flat ribbon connection

... for wiring the digital modules or for 1-,

2- or 3-wire connection.

The assignment of the IM 153-2 interface module to the two active bus modules BM IM/IM can be found in chapter

"Configuring the electrical structure (Page 47)".

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды