Siemens IM 153-4 PN Скачать руководство пользователя страница 107

Страница: 107 / 274

Maintenance and service

7.4 Replacing the IM 153-2 or IM 153-2 FO

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

105

Installing a New Module

Install the new module as follows:
1.

On the IM 153-1 set the same DP address as you had on the old IM 153-1.

Insert the new IM 153-1 and swing it down.

Screw the module on securely.

Wire the IM 153-1.

Screw the bus connector firmly into place.

Put the standby switch of the power supply module into the 1 position (output voltages to

rated value).

Response of the ET 200M After Module Replacement

If there is a fault after replacing the module, with

STEP 5 or STEP 7 in the diagnostics buffer

you can view the cause of error.

7.4

Replacing the IM 153-2 or IM 153-2 FO

Initial Situation

The IM 153-2 / -2 FO is installed. A new IM 153 -2 / -2 FO of the same type should be

installed.

Slot numbering

If you have provided the modules in your system with slot numbering, when replacing

modules you must remove the numbering from the old module and then reuse it in the new

module.

IM 153-2: Pull out the bus connector

You can remove the bus connector with worn-through bus cable from the PROFIBUS DP

interface without having to interrupt the data traffic to the bus.

Note
A data communication error may occur on the network.
On both ends, the bus segment must always be connected to the terminating resistor. For

example, this is not the case when the last slave with the bus connector is deactivated. As

the terminating resistor in the bus connector obtains its voltage from the node, the function of

the terminating resistor is affected.
Ensure that the nodes to which the terminating resistor is connected are always supplied

with voltage.

Tip: Use the PROFIBUS terminator as an active bus connector.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды