Siemens IM 153-4 PN Скачать руководство пользователя страница 237

Страница: 237 / 274

Technical Specifications

10.4 Technical specifications of the IM 153-4 PN interface module

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

235

Isochronous real-time communication

Synchronized transmission method for the cyclic exchange of IRT data between PROFINET

devices.
A reserved bandwidth is available within the send cycle for IRT IO data. The reserved

bandwidth ensures that IRT data can be transferred at reserved synchronized intervals,

without being influence by other higher network loads (e.g. TCP/P communication, or

additional real-time communication).
The "high flexibility" IRT option enables the best possible flexibility. It is not necessary to

configure the topology.
For further information please refer to the STEP 7 Online Help and the "PROFINET System

Description (

http://support.automation.siemens.com/WW/view/en/19292127

)" manual.

Prioritized startup

Prioritized startup denotes PROFINET functionality for accelerating the startup of IO devices

for RT and IRT communication within a PROFINET IO system.
The function reduces the time that the correspondingly configured IO devices require to

recover the cyclic exchange of user data in the following situations:
●

after power has returned

●

after station recovery

●

after activation of IO devices

Note
Ramp-up time depends on the number and type of modules. Also note that the minimum

ramp-up time increases by 1.5 seconds if you are using the active backplane bus.

For further information please refer to the STEP 7 Online Help and the "PROFINET System

Description (

http://support.automation.siemens.com/WW/view/en/19292127

)" manual.

Device replacement without removable media / programming device

IO devices having this function can be replaced easily:
●

You do not require any removable storage medium (for example, SIMATIC Micro Memory

Card) with saved device names.

●

The device name does not have to be assigned using the programming device.

Instead of being assigned a device name from the removable medium or programming

device, the IO device is now assigned a device name by the IO controller. The IO controller

uses the configured topology and the correlations derived from the IO devices. The

configured target topology must agree with the actual topology.
For further information please refer to the STEP 7 Online Help and the "PROFINET System

Description (

http://support.automation.siemens.com/WW/view/en/19292127

)" manual.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды