manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 185

 

Functions 

 

8.9 SNMP 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

183

 

8.9

 

SNMP 

The Simple Network Management Protocol (SNMP) is the standardized protocol for 

diagnosing and configuring the Ethernet Network infrastructure. SNMP-based applications 

can be operated parallel to applications with PROFINET on the same network. 

Properties 

The IM 153-4 PN supports the SNMP Ethernet service. LLDP-MIB and MIB-2 (RFC1213) are 

supported. R / W objects can be changed using SNMP tools and are saved in the module.   
Following replacement with a factory-new module, the R / W objects of the interface module 

are set to factory settings. 

Resetting SNMP parameters to factory settings 

 

NOTICE 

 

When factory settings are restored, the stations in a line can fail. 

 

"Reset to factory settings" is only possible if the IO device is not exchanging data with an IO 

controller. 
To reset retentively-stored SNMP parameters to factory settings (

STEP 7 V5.4 SP 2 and 

higher), select Target system > Ethernet > Edit Ethernet node and press the Reset button 

under Reset to factory settings.  
The following data is not deleted when resetting: 
●

 

The MAC address 

●

 

I&M data 

 

 

 

Note 
With the IM153-4AA01 interface module it is possible to reset to factory settings also 

during the data exchange with a controller. The station is unavailable during this 

resetting. 
The maintenance data 1, 2 and 3 (I&M1, I&M2 and I&M3) are also reset with this 

interface module. 

 

 

 

Note 
Deleting the device name 
The device name is deleted after resetting to factory settings 

 

Having deleted the device name you can then assign a new device name. Open the 

properties dialog box of the interface module in HW Config. Confirm the properties dialog 

box without entering a device name in the "Assign device name" field. 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды