Siemens IM 153-4 PN Скачать руководство пользователя страница 131

Страница: 131 / 274

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

129

Functions

8.1

Support for I/O modules with expanded input data

The IM 153-2BAx2 interface module supports I/O modules with expanded input data

(> 16 bytes). For more detailed information, refer to the documentation on the respective

modules.

Expanded output data are not supported.
For the ET 200M, this means that:
●

The I/O module in use must support provision of expanded input data.

●

The IM 153-2BAx2 supplies the substitute value "0" in the expanded input data of an I/O

module that is starting up or that has been removed.

●

The total amount of input data must not exceed the following values:
–

128 bytes per slot

–

244 bytes per IM 153-2BAx2. i.e., per ET 200M

These limits are checked during configuration.

●

"Standard" and expanded input data are internally consistent but not consistent relative to

each other.

The following figure illustrates this point.

%\WH
%\WH
%\WH

%\WH
%\WH
%\WH
%\WH

XSWR
PD[
E\WH

ಯ6WDQGDUGರLQSXWGDWD
DOOE\WHVDUHFRQVLVWHQW

6XEVWLWXWHYDOXHVDUHGHWHUPLQHG
IURPWKHPRGXOHW\SH
HJ)))

IRUDQDORJ

VLJQDOPRGXOHV

&RQVLVWHQF\OLPLW

([SDQGHGLQSXWGDWD
DOO[E\WHVDUHFRQVLVWHQW

7KHVXEVWLWXWHYDOXHVDUHಯರ

The expanded input data are updated in longer time intervals than the "standard" input

data.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды