manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 247

 

Compatibilities between the IM 153-x 

 

A.2 Compatibilities between the versions of IM 153-2 / -2 FO 

ET 200M 
Operating Instructions, 12/2008, EWA-4NEB780600602-08 

245

 

Configurable FM in a configuration with IM 153-2 

For the distributed use of the FM 353 / 354 / 355 with full S7 functionality you can use the 

following CPUs and FMs only as of the specified order numbers and module versions. 
CPUs and FMs not listed in the table (e.g. CPU 316-2 DP) can be used as of the respective 

first module version. 

Table A- 2 

Restrictions for DP master CPUs and FM for IM 153-2 

Module 

as of order no. 

... with module version 

Operating system update is 

possible as of version module 

CPU 315-2 DP 

6ES7315-2AF01-0AB0 

03 

01 

CPU 413-2 DP 

6ES7413-2XG01-0AB0 

02 

01 

CPU 414-2 DP  

6ES7414-2XG01-0AB0 
6ES7414-2XJ00-0AB0 

02 
04 

01 
03 

CPU 416-2 DP 

6ES7416-2XK00-0AB0 
6ES7416-2XL00-0AB0 

04 
04 

03 
03 

FM 353 
FM 354 
FM 355C 
FM 355S 

6ES7353-1AH01-0AE0 
6ES7354-1AH01-0AE0 
6ES7355-0VH10-0AE0 
6ES7353-1VH10-0AE0 

01 
01 
01 
01 

– 
– 
– 
– 

Configuration of the IM 153-2 with the general ID format (AKF) 

You can also configure the IM 153-2 as of order number 6ES7153-2AA02-0XB0, module 

version 07, and 6ES7153-2AB01-0XB0, module version 06, with the general ID format AKF. 

This configuration assumes detailed knowledge of the structure of the AKF. You must use 

the code 0x00 for the slots 1 to 3. 

 

WARNING 

 

If you conduct the configuration with the general ID format AKF, the quality of the 

comparison of the preset and actual configuration when the DP slave starts up or when 

removing or inserting modules is very low. Since there is no type ID available for the 

comparison, an incorrect configuration cannot be easily detected! 

 

Functionality of the Previous Version 

If you insert the IM 153-2Bx00 interface module 
●

 

on a bus module BM IM/IM (6ES7195-7HD00-0XA0), 

●

 

configure as an IM 153-2AA02 / -2AB01 with 

STEP 7, 

●

 

configure with GSD revision 2, 

then it has the functionality of an IM 153-2AA02 / -2AB01. 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды