Siemens IM 153-4 PN Скачать руководство пользователя страница 242

Страница: 242 / 274

Technical Specifications

10.6 Using the ET 200M in the potentially explosive area zone 2

ET 200M

240

Operating Instructions, 12/2008, EWA-4NEB780600602-08

Switchover Time in the Case of Redundancy

The switchover times, dependent on the mode and configuration amounts to:

DP master system

ET 200M

with

IM 153…

Switchover time

Configuration

-2AA02

70 ms

any configuration

-2AB01

30 ms

… without F-, FM- or HART modules.

30 ms

any configuration

S7-400H

-2Bx00

-2Bxx1

30 ms

… without F-, FM- or HART modules.

-2AA02

70 ms +

2 DP-cycles

any configuration

-2AB01

30 ms +

2 DP-cycles

… without F-, FM- or HART modules.

30 ms

any configuration

S7-software

redundancy;

S5-115H / 155H

-2Bx00

-2Bxx1

30 ms

… without F-, FM- or HART modules.

If the response monitoring time is set greater than 30 ms or 70 ms, the switchover time

corresponds to the set monitoring time.

Delay time of the input / output modules

The delay time of the input / output modules can be derived from the technical specifications

of the modules (refer to the "S7-300 automation system, module specifications

(

http://support.automation.siemens.com/WW/view/en/8859629

)" reference manual).

10.6

Using the ET 200M in the potentially explosive area zone 2

See product information "Use of subassemblies/modules in a zone 2 hazardous area

(

https://portal.automation.siemens.com/apps/meta-

search_p/index.ad.nwa.EN.html?q=19692172

)".

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды