Siemens IM 153-4 PN Скачать руководство пользователя страница 129

Страница: 129 / 274

Maintenance and service

7.11 Saving data and updating the IM 153-4 PN

ET 200M
Operating Instructions, 12/2008, EWA-4NEB780600602-08

127

Example configuration

Update from PD / PC via PROFINET IO (direct)
The PG / PC with the update files is directly connected to the PROFINET interface of the

IM 153-4 PN (refer to the following figure).

Note
If no

STEP 7 project containing the respective IM 153-4 PN is available, the update can also

take place via the online view (available nodes) in

STEP 7.

3*3&

(70

,031

Figure 7-7

Update via PROFINET IO (PG / PC directly on IM 153-4 PN)

Update via SIMATIC Micro Memory Card
The following SIMATIC Micro Memory Cards are available for the update:

Table 7- 4

Available SIMATIC Micro Memory Cards for an update of the IM 153-4 PN

Type

Order numbers

SIMATIC Micro Memory Card 2M

6ES7953-8LL20-0AA0

SIMATIC Micro Memory Card 4M

6ES7953-8LM20-0AA0

SIMATIC Micro Memory Card 8M

6ES7953-8LP20-0AA0

To perform an update via SIMATIC Micro Memory Card, proceed as follows:
1.

Use

STEP 7 and your programming device to transfer the update files to a SIMATIC

Micro Memory Card. The data saved on the SIMATIC Micro Memory Card is then

overwritten by the update files.

3*3&

Switch off the voltage to the IM 153-4 PN.

Remove the existing SIMATIC Micro Memory Card containing the device name from the

module slot.
To eject the SIMATIC Micro Memory Card, push in the ejector in the lower section of the

module slot with a small screwdriver or ball-point pen.

Содержание IM 153-4 PN



















































































































































































































































































Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды

Siemens IM 153-4 PN, Руководство по эксплуатации

Результаты поиска

Содержание IM 153-4 PN

Отзывы:

Бренды по названию

Популярные бренды