manualshive.com logo in svg

Siemens IM 153-4 PN, Руководство по эксплуатации

Поделиться
Скачать
Siemens IM 153-4 PN Скачать руководство пользователя страница 100

Commissioning 

 

6.2 PROFINET IO 

 

ET 200M 

98

 

Operating Instructions, 12/2008, EWA-4NEB780600602-08 

6.2.3

 

Assigning device names to the I/O device 

Introduction  

Each PROFINET IO device is assigned a unique device ID at the factory (MAC address).     
For configuration and in the user program, each ET 200M IO device is addressed with its 

device name.  
For detailed information on addressing in PROFINET IO, refer to the "PROFINET System 

Description (

http://support.automation.siemens.com/WW/view/en/19292127

)" system 

manual. 

Requirements 

●

 

Interface Module IM 153-4 PN 

●

 

up to IM 153-4AA00-0XB0: SIMATIC Micro Memory Card 64k and higher 

●

 

The programming device must be online on PROFINET to the IO device to let you assign 

a device name to the interface module. 

●

 

The IO device is configured in HW Config and assigned an IP address. 

Assigning device names   

1.

 

For IM 153-4AA00-0XB0: 
Insert an empty SIMATIC Micro Memory Card into the module slot on the front of the 

IM 153-4 PN interface module. 

2.

 

Switch on the voltage supply for the IM 153-4 PN. 

3.

 

In HW Config, open the "Properties - IM 153-4 PN" window, enter the device name for the 

IO device, and then confirm your entry with "OK". 
Do not use the device name "noname". 

Transferring the device name to the interface module. 

1.

 

In HW Config, select "PLC > Ethernet > Assign Device Name". 

2.

 

Click "Assign Name" in the "Assign Device Name" window. 

Result 

The device name is saved on the SIMATIC Micro Memory Card in the IM 153-4AA00-0XB0 

interface module.  
As of IM 153-4AA01-0XB0, the device name is saved in the interface module. 

Содержание IM 153-4 PN



















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды